Teknatool International

Getting Started 1

• How to use a chuck

General ALL lathes 29

• Centering your NOVA Lathe (with movable headstock) using the NOVA Acruline 2MT Accessory
• Adjusting the position of the Toolslide lock handle.
• FAQ ALL // SPINDLE THREAD DAMAGE
• How to change the bearings on Nova Series Lathes
• Proposition 65 Warnings for Californian Residents

View all 29

Product Reviews 1

• Voyager reviews

Repairs 0

Firmware and Factory Reset 1

• GD32 Boot Loader Instructions

NOVA Lathes 13

• NOVA Comet II Midi Lathe
• NOVA 1624 II Lathe
• NOVA DVR Galaxi Lathe
• NOVA DVR Saturn Lathe
• NOVA DVR XP Control Panel Upgrade

View all 13

NOVA Chucks and Accessories 13

• NOVA Chuck Accessory Jaw Manual
• SuperNOVA2 Chuck Manual
• NOVA G3 Chuck
• NOVA Precision Midi Chuck
• NOVA Titan III Chuck

View all 13

NOVA Drill Presses 7

• NOVA Voyager DVR Drill Press Manual
• NOVA Vulcan DVR Drill Press Manual
• Common Woodworking Terms & Their Meaning
• Downfeed
• Drill Press low voltage

View all 7

NOVA Catalogs 6

• Chucks and Jaws Catalog 2017-2018
• NOVA Comet II Brochure
• NOVA 1624 II Woodlathe Brochure
• NOVA Saturn DVR Lathe Brochure
• NOVA Voyager DVR Drill Press Brochure

View all 6

NOVA Discontinued Products 10

• Teknatool TL-1000 lathe
• Teknatool TL-1200 lathe
• NOVA TL-1500 lathe
• NOVA 3000 lathe
• NOVA Mercury mini-lathe

View all 10

Certifications 7

• NOVA 1624 II Certification of Conformity
• NOVA Comet II Lathe Certificate of Conformity
• NOVA Galaxi Lathe Certificate of Conformity
• Certificate of Conformity for ESO / RCM - Non Rewireable Plug
• NOVA Voyager Drill Press Certificate of Conformity

View all 7

NOVA Accessories 4

• Wireless Remote II
• How do I know if I have a genuine NOVA accessory?
• NOVA Modular Toolrest System Manual
• Magnetic Lamp

General DVR Machine FAQs 31

• FAQ DVR RPS ERRORS and LOW! speed readout
• FAQ DVR STOP/START Fault/Error/No Voltage/Low Voltage
• FAQ DVR XP/2024 INDEX MECHANISM LOOSE/RATTLING NOISE IN HEADSTOCK
• Quill Jammed Or Will Not Slide Into Tailstock Body All The Way 1624, Dvr Xp, DVR 3000
• DVR RETROFIT 55523 CONTROL PANEL UPGRADE COMPATIBILITY

View all 31

General Chuck 25

• Identify your NOVA chuck
• FAQ SUPERNOVA, NOVA SCROLL AND G3 ARE SOMETIMES CONFUSED WITH EACH OTHER
• NOVA G3 CHUCK two versions explanation.
• Chuck INSTRUCTION MANUALS + Cleaning your Chuck
• WHY the Powermatic 90 and Conover lathes won't work with Nova chucks/adapters

View all 25

General Jaws & Accessories 13

• Woodworm Screw FAQs
• FAQ Compatibility of NOVA infinity system with existing NOVA products
• JAW RANGE SPECIFICATIONS
• FAQ Chuck and Accessory Jaw Compatibility
• Capacity of Jaws when mounted on particular chucks

View all 13

46300 Comet II 19

• FAQ 46300 COMET II THREAD SIZES
• FAQ COMET II HEADSTOCK NOISE
• Aligning the Centres of the Comet 2 Lathe
• Vibration Problems with the Nova Comet Lathe
• FAQ How to adjust the belt on 46300 Comet II if there is not enough space

View all 19

NOVA 1624 II Lathe 11

• NOVA 1624 II Motor Reversed Issue
• How to replace the belt, spindle and bearing on the NOVA 1624-II lathe
• NOVA 1624-II Studs nuts loosening during use
• How to take the tailstock quill apart on the NOVA 1624-II
• How to replace the motor pulley when upgrading to the DVR motor

View all 11

DVR 3000 Lathe 5

• NOVA DVR 3000 POWER PROBLEMS
• Aligning & Servicing the adjustable Tailstock of the NOVA 3000 Woodlathe
• Installing the new main board into the NOVA DVR3000 Headstock
• SRM ERROR
• NOVA DVR 3000

DVR XP Lathe 10

• How to enter Service Mode and Check serial no. & parameter on DVR XP lathe.
• How to enter Rotor Position Test (phase) Function on DVR XP or DVR SATURN Lathe
• DVR XP HEADSTOCK DETENT MECHANISM BINDING/NOT SEATING/HEADSTOCK WOBBLE
• How to Replace the sensor board on XP lathe
• How to change the DVR XP control board

View all 10

DVR GALAXI 1644 14

• How to enter service mode on the Galaxi DVR 1644 lathe
• How to run the motor position test on the Galaxi DVR 1644 lathe
• How to remove the control board
• How to remove the headstock on the DVR Galaxi 1644
• How to replace the control board on the DVR Galaxi 1644

View all 14

DVR 2024 Lathe 6

• Rotor Position Test Function on DVR 2024 Lathe
• How to enter Service Mode and Check parameter on DVR 2024 lathe.
• Removing the Nova DVR 2024 Woodlathe's Headstock
• NOVA 2024 and NOVA DVR Wireless Remote II (SKU 55522) Compatibility
• How to take the tailstock apart on the NOVA DVR 2024 Woodlathe

View all 6

DVR Voyager Drill Press 40

• NOVA Voyager DVR Drill Press FAQs
• How to enter Service Mode on NOVA Voyager DVR Drill Press
• Rotor Position Test on the NOVA Voyager DVR Drill Press
• Calibrating the depth (height) sensor on the Voyager
• Recommended Speeds for Materials

View all 40

DVR 3000/XP/2024 Control Panel Upgrade 2

• What lathes are compatible with DVR XP Panel Upgrade?
• What is the purpose of the short USB cable?

NOVA DVR Wireless Remote 2

• NOVA DVR WATCH style Wireless Remote I FAQs
• Wireless Remote II Install Guide

COLE JAWS 3

• COLE JAW SET APPEARS TO BE MISSING JAW SCREWS
• COLE JAW INFO - RANGES - SPECS
• COLE JAWS with G3 CHUCK TBAR HANDLE

NOVA 3000 BELT LATHE 1

• Bearings for NOVA 3000 Lathe with Leeson motor

NOVA Vulcan 4

• New Combined Spindle on the NOVA Vulcan
• Vulcan vs. Voyager
• How to replace the Main Control Board on the NOVA Vulcan DVR
• Can I use the voyager firmware update on the vulcan?

DVR Viking Drill Press 83700 12

• Viking Headstock Alignment
• Viking + Mortising Attachment
• Adjusting the laser modules on the NOVA Viking Drill Press
• Replacing the main board for the Nova Viking 16" Drill Press
• Calibrating the Depth Sensor for the Nova Viking 16" Drill Press

View all 12

Updated DVR FAQs 24

• How to fix the Hardware Fault at low RPM for DVR Saturn DVR Orion and DVR Voyager
• How to upgrade HMI firmware for DVR using NOVA firmware uploader or ST-Link
• How to Align Tailstock with Spindle for DVR Lathes
• How to Check for Runout on NOVA Lathes and Drill Presses
• How to Enter Service Mode on NOVA DVR 2024

View all 24

14DR 1

• 14DR Controller Replacement

Nova Neptune & Neptune MAX 1

• How to reset the position of the index lock on the Nova Neptune and Neptune MAX lathes